Difference between revisions of "Resize Root Filesystem"

From wikipost
Jump to navigationJump to search
Line 118: Line 118:
losetup --find --partscan imagefile.dd
losetup --find --partscan imagefile.dd
Reveal the partition devices that were assigned:

Revision as of 18:15, 20 January 2021

This procedure details how to copy the current filesystem to a new disk. This is a preferred scenario when:

  • the current root filesystem is becoming too small
  • you wish to shrink the existing root filesystem (think vm's)

Steps to achive the copy are:

  • create or attach a new disk
  • create a root (and swap partition) on the disk (fdisk /dev/...)
  • format the disk with EXT2
  • mount the disk to a directory on the live system
  • copy all files to the new disk
  • copy the special device files (?)
  • chroot into the new disk
  • install the bootloader to the MBR of the new disk

Copy command:

(cd / ; tar -cf - . --one-file-system) | (cd /mnt/ ; tar xvfpB -)

Find out the new disk's UUID:

ls -l /dev/disk/by-uuid/

  • Update the new UUID in /etc/fstab
  • Update the new UUID in /boot/grub/grub.cfg

Install bootloader:

There are (as far as I know of) three ways of installing GRUB onto the new disk.

1 * After copying all files, remove the old drive and boot off a live Linux CD (e.g. Knoppix) (the idea here is that hd0 is the new drive and issuing the grub-install command will simply install on hd0.

2 * Swap the drives (master becomes slave, slave becomes master) and in the BIOS designate to boot of the second disk. (again, grub will install on hd0 which is the new disk)

3 * with the new disk attached as /dev/sdb, instruct GRUB to install there but to refer to it as /dev/sda (or hd0 as we want). (my preference)

Method 1 and 2


Method 3

(with the new disk (/dev/sdb) still mounted at /mnt/)

grub-install -d /mnt /dev/sdb
  • shutdown
  • take out old disk, and replace with the new disk as the primary boot disk
  • start the machine

GRUB v1 only:

When you're back in the O/S update the menu.lst to make sure the correct boot device (e.g. /dev/sda) is used.

grub-install /dev/sda
  • reboot and all should be fine

Resize Filesystem in an image

So now you have a dd image of your disk and found out that the device you wish to restore it to is smaller in size...

All good, what we do next is to resize the filesystem inside the dd image.

Just to be sure we understand the terminology:

  • a block device is the physical capacity of a storage device (e.g. an 8GB Flash drive)
  • a partition is a logical storage container that is created on the block device. A block device can hold multiple partitions.
  • a filesystem is a logical arrangement of data that is used by an operating system to save and read files. A partition usually holds only one filesystem.

If we want to make a larger partition fit on a smaller partition we need to make sure that the used space inside the larger partition doesn't exceed the size of the smaller partition. Once we know this, the process is relatively simple:

  • attach a loop device to the disk-image (using losetup)
  • run a filesystem-check on the partition we wish to resize (using e2fsck)
  • shrink the filesystem to the desired size (using resize2fs)
  • shrink the partition to a size that is (slightly) larger than the filesystem

After this, we can just write the disk image to the (smaller) block device without running into disk space issues

The Process:

Attach a loop device to the various partitions inside the disk image:

losetup --find --partscan imagefile.dd

Reveal the partition devices that were assigned: